Specifications |
Analog Input |
Input Channels | 6 (Differential) |
Input Type | +/-500 mV, +/-1V, +/-5 V, +/-10 V |
+0 mA ~ +20 mA, +/-20 mA, 4 ~ 20 mA (Jumper Selectable) |
Resolution | Normal Mode | 16-bit |
Fast Mode | 12-bit |
Sampling Rate | Normal Mode | 10 Samples/Sec.(Total) |
Fast Mode | 60 Samples/Sec. (Total) |
Accuracy | Normal Mode | +/-0.1% |
Fast Mode | +/-0.5% or better |
Bandwidth | Normal Mode | 15.7 Hz |
Fast Mode | 78.7 Hz |
Zero Drift | +/-20 uV/°C |
Span Drift | +/-25 ppm/°C |
Input Impedance | Voltage Input: 2M O, Current Input: 125 O |
Common Mode Rejection | 86 dB Min. |
Normal Mode Rejection | 100 dB |
Open Wire for Current Output | 4 ~ 20mA |
Over Protection | 240 Vrms |
ESD Protection | +/-4 kV (Contact for each channel) |
+/-8 kV air for random point |
EFT Protection | +/-4 kV for Power |
Analog Output |
Output Channels | 2 |
Span Drift | +0 V~ +5 V, +/-5 V, +0 V~ +10 V, |
+/-10 V,+0 mA ~ +20 mA, +4 mA ~ +20 mA (jumper selectable) |
Resolution | 12-bit |
Accuracy | +/-0.1% of FSR |
Voltage Output Capability | 10 [email protected] mA |
Current Load Resistance | 500 Ohms |
Power-Up and SafeValue | Yes |
Open Wire for Current Output | 4 ~ 20mA |
Digital Output |
Output Channels | 2 (Sink) |
Output Type | Isolated Open Collector |
Max. Load Current | 700 mA/Channel |
Load Voltage | 5 VDC ~ 50 VDC |
External Power Reversed Protection and Short Circuit Protection | Yes |
Over-Temperature Protection | Yes, 150°C |
Current limited Protection | 1.1 A |
Digital Input |
Input Type | 2 (Dry+Wet) |
Dry Contact(Source) | On Voltage Level | Close to GND |
Off Voltage Level | Open |
Effective Distance for Dry Contact | 500M Max. |
Wet contact | On Voltage Level | +1 VDC Max. |
Off Voltage Level | +3.5 VDC ~ +30 VDC |
Counters | Channels | 2 |
Max. Counts | 16-bit (65535) |
Max. Input Frequency | 50 Hz |
Min. Pulse Width | 10 ms |
System |
CPU | 80186 CPU (80 MHz) |
SRAM | 512 KB |
Flash Memory | 512 KB |
EEPROM | 16 KB |
Dual Watchdog | Yes |
Communication |
PoE Ethernet Port | 10/100 Base-TX (With Link, Activity LED Indicator) and automatic MDI/MDI-X |
2-way Isolation |
Ethernet | 1500 VDC |
AI, AO,DI and DO | 2500 Vrms |
LED Indicators |
PoE | PoE On |
L1 | Run |
L2 | Link/Act |
L3 | 10/100 M |
Power Requirements |
IEEE 802.3af | Class 1 |
Required Supply Voltage | Powered by Power-Over-Ethernet (PoE) or auxiliary power +12 ~ +48 VDC(non-regulated) |
LED Indicator | Yes |
Power Consumption | 0.12 A @ 24 VDC Max. |
Mechanical |
Dimensions (W x H x D) | 72 mm x 123 mm x 35 mm |
Installation | DIN-Rail or Wall mounting |
Environment |
Operating Temperature | -25°C ~ +75 °C |
Storage Temperature | -30°C ~ +80 °C |
Relative Humidity | 5 ~ 90% RH, non-condensing |
Software Specifications |
Functions |
36 IF-THEN-ELSE Logic Rules | 3 IF conditions with AND or OR operators |
3 THEN actions |
3 ELSE actions |
48 Internal Registers | Hold temporary variables and read/write data via Modbus/TCP address. |
12 Timers | Delay / Timing functions. |
12 Emails | Send Email messages to pre-set Email receivers. |
Rule Configuration Website | Access Web server on WISE controllers to edit and upload logic rules through web browser. |
Modbus/ TCP Protocol | Real time control and monitoring I/O channels and system status of controllers via SCADA software. |
IF Conditions |
DI Channel | ON, OFF, ON to OFF, OFF to ON, Change |
AI Channel | =, >, <, >=, <=(value) |
Internal Register |
DI Counter | =, >, <, >=, <=(value), Change |
DO Counter |
Timer | Timeout, Not Timeout. |
THEN / ELSE Actions |
DO Channel | ON, OFF, Pulse Output |
AO Channel | Change the value |
Internal Register |
DI Counter | Reset |
DO Counter |
Timer | Start, Stop |
Email | Send |