| GL100-N Main Unit Specifications |
| Number of channels: | Varies by the input module used, and measurement type is fixed with each input module |
| Output signal: | Alarm (1 channel), solid state switch with optical isolation (Optocoupler, Max. load is the 30 V, 50 mA) |
| Interface to PC: | USB (micro USB B type connector) |
| Storage device: | Built-in memory: RAM (Approx. 4.9 MB)
External memory: microSD memory card
* Maximum file size for captured data is 1.9MB. It is recommended to use the microSD memory card that supports sleep mode. (Example: TS4GUSDHC4, made by Transcend) |
| Display | LCD (backlit monochrome, graphical type 128 x 64 dots)
Contents: Captured data and Setting menu (Stored data is not able to replay. It is able to replay using the PC application software.) |
| Functions: | Real-time data capturing
Display the captured data value to the LCD in real-time and save the monitoring values
Set conditions using the Menu setting |
While using USB port:
Output captured data in real-time
Output the saved data from the internal memory
Full control of the GL100 from the PC application software |
| Alarm: | Action
Outputs the signal when the measuring data reaches the present conditions of alarm
Source
Level of measuring data
Detecting method
Condition: Higher or lower (signal is higher or lower than the threshold)
Combination: or |
| Trigger: | Action
Start or stop the recording of captured data by trigger
Source
Start trigger: OFF, Level (*), Alarm, or Date
Stop trigger: OFF, Level (*), Alarm
* Level trigger is available in the analog input of the GS-4VT, GS-4TSR, and GS-3AT module.
Detecting method of the Level (*)
Condition: Rising or Falling (signal is passed through the threshold)
Combination: OR or AND |
| Dustproof and waterproof: | IP54 compatible (*)
* It is effective only in the condition that the input module is set to the GL100 and then the covers of connector and battery are closed. It is recommended to replace the packing of cover in periodically. |
| Power source: | Alkaline battery (AA size x 2)
USB bus-power (5V, 200 mA) (*)
* When AC adapter for USB device is used, the required power capacity is 5V, 1A. Battery and AC adapter is not included. |
| Operating environment: | Temperature: -10 °C to 50 °C
Humidity: up to 80 % RH (non condensed) |
| External dimension [W x D x H]: | Approx. 66 x 100 x 27 mm (exclude protrusion |
| Weight: | GL100-N: Approx. 125 g |
| GS-CO2 Carbon Dioxide Sensor Specifications |
| GS-CO2: | CO2 density sensor with a measuring range of 0-9,999 ppm concentration. |
| Sensor Method: | NDIR System (non-disperv infrared) |
| Measurement Data: | CO2 Concentration |
| Measurement Channels: | 1-ch |
| Measurement Range: | 0 to 9,999 ppm |
| Measurement Accuracy: | ±(5% of rdg + 30 ppm) In the range between 0 and 5000 ppm |
| Response Time: | 3 minutes or less |
| Sampling Intervals: | 0.5 | 1 | 2 | 5 | 10 | 20 | 30 sec
1 | 2 | 5 | 10 | 20 | 30 | 60 min
CO2 sampling interval is 2 seconds or slower. For sampling selection slower than 2 seconds, same values are recorded and new values are updated every 2 seconds. |
| Calibration: | ON / OFF |
| Extension Cable: | Approximately 20 cm |
| Operating Environment: | 0º to 50ºC, 80% RH and below (non-condensed) |
| External Dimensions: | 66 mm x 100 mm x 24.6 mm (excludes protrusion) |
| Weight: | 99 g (3.49 oz) |
