| Item | Description |
| Number of channel | Up to 4 channels |
| Interface to PC | USB 2.0 |
| Functions | Real-time data capturing
Display the captured data value to the LCD in real-time and save the monitoring values
Set conditions using the Menu setting |
While using USB port:
Output captured data in real-time
Output the saved data from the internal memory
Full control of the GL100 from the PC application software |
| Display | LCD (backlit monochrome, graphical type) |
| Storage device | Built-in RAM (Approx. 4.9 MB)
micro SD memory card
* Maximum file size for captured data is 1.9 GB. |
| Sampling interval | 0.5 to 30 seconds and 1 to 60 minutes |
| Output signal | Alarm (1 channel) |
| Power source | Battery (AA x 2)
USB bus-power (micro USB connector)
* The required power capacity is 5V, 1A when AC adapter for microUSB drive is used. AC adapter is not included. |
| Operating environment | Temperature: -10 ºC to 50 ºC
Humidity: up to 80% RH (non condensed)
Water resistance: IP54 |
| External dimension | Approx. 66 x 100 x 27 mm (exclude protrusion) |
| Weight | GL100-N: Approx. 125 g, GL100-WL: Approx. 130 g |
| Temperature & Humidity sensor (GS-TH) |
| Type of measurement | Temperature, and Humidity
Accumulated temp. (calculated value), Dew-point temp. (calculated value) |
| Measuring range | Temperature: -20 to 85 ºC Humidity: 0 to 100 % RH |
| Acceleration & Temperature sensor (GS-3AT) |
| Type of measurement | Acceleration in 3-axis (X-, Y-, Z-axis), and Temperature |
| Measuring range | Acceleration: ±2 (20 m/s²), ±5 (50 m/s²), ±10G (100 m/s²)
Temperature: -10 to 50 ºC |
| Sampling interval | 5 to 100 ms in memory mode, 0.5 s to 60 min. in direct mode (*¹) |
| Illuminance & Ultraviolet sensor (GL-LXUV) |
| Type of measurement | Illuminance, and UV intensity Accumulated Illuminance (calculated value), Accumulated UV intensity (calculated value) |
| Measuring range | Illuminance: 0 to 200 klx UV intensity: 0 to 30 mW/cm² |
| Carbon dioxide (CO2) sensor (GL-CO2) |
| Type of measurement | Carbon dioxide concentration |
| Measuring range | 0 to 9999 ppm |
| Operating environment | Temperature: 0 ºC to 50 ºC, Humidity: up to 80% RH (non condensed) |
| AC Current sensor adapter (GS-DPA-AC) |
| Type of measurement | Current
Power (calculated value), Electric energy (calculated value) |
| Application circuit | Single-phase two-wire, Single-phase three-wire system, or Three-phase three-wire |
| Sensor | Clamp-on current probe (optional), Two (2) sensors are able to connect |
| Measuring range | 50, 100, 200 A RMS (varies by the sensor) |
| Voltage & Thermocouple input terminal (GL-4VT) |
| Number of channel | Analog voltage 4 channels, Logic or Pulse 4 channels (*²) |
| Measuring range | Voltage: 20mV to 50V, 1-5V FS Thermocouple: K type (-200 to 1370 ºC) & T type (-200 to 400 ºC)
Logic (signal pattern): 0 to 24 V (common ground)
Pules (count): Max. 200 counts/sampling intervall, accumulating up to 65535 counts |
| Temperature sensor input terminal (GL-4TSR) |
| Number of channel | Sensor 4 channels, Logic or Pulse 4 channels (*²) |
| Sensor | Thermistor sensor (optional) |
| Measuring range | Temperature: -40 to 120 ºC (varies by the type of sensor)
Logic (signal pattern): 0 to 24 V (common ground)
Pulse (count): Max. 200 counts/sampling interval, accumulating up to 65535 counts |
